Subaru Forester
+ Subaru Forester cars
+ Maintenance instruction
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
- Engine electric equipment
Specifications
Start of the engine from the auxiliary power supply
Removal and installation of the rechargeable battery
Check of a state and replacement of wires of the battery
System of ignition - the general information and precautionary measures
Check of serviceability of functioning of system of ignition
Assembly of coils of ignition - the general information, check of a state and replacement
Check and adjustment of installation of a corner of an advancing of ignition
Replacement of the module of ignition
Check of serviceability of functioning of CKP, CMP sensors and detonation
Service of spark plugs
Check of a condition of high-voltage wires
System of a charge - the general information and precautionary measures
Generator, general information, check and service
Removal and installation of the generator
System of start - the general information and precautionary measures
Check of serviceability of functioning of a starter and chain of start
Nippondenso starters - check and service
Mitsubishi starters - check and service
+ Control systems of the engine
+ Gear shifting box
+ Coupling, transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Service of spark plugs See also information provided in the Section Check of a State and Replacement of Spark Plugs in the Head Routine maintenance.
|
|
All spark plugs established on the engine have to have identical kalilny number.
|
Removal
Spark plug of the first cylinder
Design of the drive of the face key applied to removal/installation of spark plugs
|
|
1. Disconnect a negative wire from the battery.
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! |
2. Disconnect an electrical wiring from the MAF sensor (see Chapters of the Power supply system and release and the Control system of the engine).
3. Release four clamps and remove the top cover of the air cleaner (see the Head of the Power supply system and release).
4. Release a fixing collar and disconnect an inlet air duct from the top cover of the air cleaner. |
| 5. Take the air filter and release four screws of fastening of the case of the air cleaner. Remove the air cleaner. |
|
| 6. Accurately disconnect VV a wire from a spark plug of the first cylinder, - pull only for a tip of the contact socket and by no means for a wire! |
|
7. Put on the head of a candle key collected with the cardan drive of a face key a spark plug of the first cylinder.
|
|
For a reversing of candles it is necessary to use a special candle head with a rubber insert like PROTO 5020-50 protecting the porcelain insulator of a candle from damage. Observance of dimensional characteristics of elements of the drive of a candle key will allow to facilitate implementation of the procedure considerably. |
|
|
| 8. Before turning out a candle cover with rags the lines of a hydraulic path of ABS laid on proximity. |
|
|
Spark plug of the second cylinder
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! |
|
|
|
|
1. Disconnect a negative wire from the battery.
2. Remove the rechargeable battery. |
| 3. Accurately disconnect VV a wire from a spark plug of the second cylinder, - pull only for a tip of the contact socket and by no means for a wire! |
|
| 4. The reversing of a candle is made in the manner similar described above for a candle of the first cylinder. |
|
Spark plug of the third cylinder
|
|
VV wire of a spark plug of the third cylinder |
Spark plug of the fourth cylinder
|
|
If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that you have the correct combination for input of the audio system in action! |
|
|
1. Disconnect a negative wire from the battery.
2. Remove the rechargeable battery. |
3. Turn out bolts of fastening of the tank these washing of glasses.
|
|
In order to avoid losses of the washing liquid do not disconnect hoses from the tank. |
|
|
| 4. Disconnect an electrical wiring from the pump of supply of liquid of washing of glasses. |
|
| 5. Raise the tank of liquid of washing of glasses and tie up it a wire. |
|
| 6. Disconnect VV a wire from a spark plug of the fourth cylinder. |
|
| 7. On models with AT cover with rags of the line of cooling of ATF. |
| 8. The reversing of a candle is made in the similar manner described above for candles of other cylinders, - get a candle key from placement of the pallet of the battery as it is shown on an illustration. |
|
|
Installation
Installation is made upside-down taking into account the next moments: In order to avoid damage of a carving to niches of the heads made of soft metal it is the best of all to make a nazhivleniye of candles for the piece of a rubber hose which is put on their shaft, - in case of a distortion the hose just will begin to be turned; Tighten candles with the required effort (20.6 ± 2.9 Nanometers).
|
|